How To Remove Sliding Glass Doors: DIY Guide
Start by prying a flathead screwdriver to remove the threshold, followed by unscrewing the brackets from the door at the top, middle, and bottom. Once you remove all the screws, lift the door up and make sure that it is completely removed from the bottom track of the door frame. Use the Phillips screwdriver to loosen the adjustment screws so you can pull up the rollers. You should now be able to freely lift the sliding glass door out of the frame and out of the track. You may need the Philips screwdriver again to free the door from the track. Once removed, have your partner help you tilt it and move it out of the doorway.
There are many reasons you may need to remove a sliding glass door, including repairing or replacing panes, restoring the proper slide, or moving large objects like furniture. Learn how to remove a sliding glass door with these instructions from the expert technicians at Glass Doctor.
Before we get into the how to remove sliding glass doors from frame process of removing a sliding glass door, make sure you have all the necessary supplies.
Sliding glass doors are a lot heavier than they look and moving it yourself could be dangerous. Have a friend froom hand to help you brace and move the door!
This is particularly important if any part of the door is stuck. Forcing a stubborn door could lead to cracks or damage how to remove sliding glass doors from frame the track or door frame. A partially removed door or unfinished project leaves your home with an how to help a victim of child abuse opening.
We fix your panes! Skip to main content. Your health and safety are our highest priority during this time. Click here for our precautionary measures. Still open to serve you. How to Remove a Sliding Glass Door Before we get into the step-by-step process of removing a sliding glass door, make sure you have all the necessary supplies. Prep the Floor Foam sheets or thick blankets will protect your floor from any chipping or cracks due to the weight of the sliding glass door.
It will also protect the door itself as you set it down. Remove the Screen Door Using a gllass screwdriver, carefully lift the rollers of the screen door off the bottom track. Once removed, move the screen door to a safe place away from your work area. Sometimes raised flooring presents this issue.
Use a flat-head screwdriver to remove the threshold and unscrew the top, middle and bottom brackets. Lay the stationary door down gently on a foam sheet. Slide the door till it hits this point. Sometimes these screws are covered in plugs that are usually easy to remove. Use the Phillips screwdriver to loosen the adjustment screws so you can pull up the rollers. You should now be able to freely lift the sliding glass door out of the frame and out of the track. You may need the Farme screwdriver again to free the door frrom the track.
Once removed, have your partner help you tilt it and move it out of the doorway. Then, gently lay it flat on a foam sheet.
Jun 24, · The simple way to remove sliding glass doors On the bottom edge of the door, you’ll notice a cap. Remove this cap, because as you’ll notice, it is covering a gap – inside of which is a screw. Feb 18, · If you want to help support Shannon to produce more videos like this, visit thismestory.com from thismestory.com-improveme. Jun 29, · If you are completely removing the sliding glass door to install a new door, you can now remove the door frame by using the pry bar. You will be doing a lot of prying to free the frame from the door jamb. Position the pry bar at the base of the trim pieces and pry upward to .
Wondering how to remove a sliding glass door? If so, there are some important things to consider. Read on to learn more. Disclaimer: REthority is supported by ads and participation in affiliate programs. We may earn a commission when you click our links. The information included in this post is for informational purposes only and should not be taken as legal or financial advice.
Sliding glass doors need to be removed periodically for cleaning, maintenance, parts replacement, or to move large pieces of furniture. You may also be replacing your existing door with a new model. The instructions you will follow below will differ based on your goal. Are you removing your sliding glass door to create space for a new door?
Are you removing the sliding glass door to replace damaged parts or for routine maintenance, like cleaning the rollers and track? Perhaps you need to remove the door so you can move a large armoire or couch into or out of your home. If you are preparing your home for new door installation or moving a large piece of furniture, you will need to remove both the sliding and stationary door panels.
Removing a sliding glass door can be a physical challenge, but it is a relatively simple process to follow. To remove a sliding glass door, you will need a few tools and materials to get started.
The flathead screwdriver or putty knife will help you tuck the sliding glass door rollers under the sliding panel as you pull it out. Depending on the screws used in your sliding glass door assembly, you may need either a flathead or Phillips head screwdriver.
You will likely need both. A pry bar with a hammer claw at one end will be necessary toward the end of the project as you begin prying the frame and stationary door parts away. A reciprocating saw can help you cut through any parts of the frame or trim that are difficult to remove.
Heavy blankets, layers of cardboard, or foam sheets are essential to protect your sliding glass doors and flooring. The bottom edges of these doors can be sharp and easily scratch or mar flooring. These doors are heavy, and their large size can make them difficult to maneuver alone. Sliding glass doors are large, and once you remove the doors from their tracks, you will need plenty of space around the area so you can carefully lay the doors on the ground.
Clear about 10 feet of space around the door, remove any furniture or objects, and ensure you have plenty of room to maneuver the doors. These are usually covered with adjustment screw covers that keep the screws out of sight. Locate these covers and use your flathead screwdriver to pry the covers off and expose them carefully.
Use either a flathead or Phillips screwdriver to turn both adjustment screws in a counter-clockwise direction, which tucks the sliding glass door rollers into the door.
It makes it flush with the track rather than sitting slightly above it on the rollers. This creates additional room for the door to clear the tracks when you pull it out. Your sliding glass door may have a doorstop that covers the inside edge of the door frame. If yours does, you will need to use your screwdriver to remove this head stop. You will find the head stop attached to the top track of your sliding glass door.
Once you remove it, be careful not to let the door fall over. Without the head stop, the door can be removed. With your helper standing beside you inside the house, carefully begin to tip or tilt the top of the door inside toward you. As you tilt the door, start lifting it up and out of the bottom track.
This is simple, with the adjustment screws in their proper position and the rollers out of the way. Note : You may or may not need this step, depending on your purpose of removing the sliding glass door. If you need to create a wide opening to move furniture or replace your sliding glass doors entirely, you will need to remove the stationary door. The other stationary door panel is likely located behind the sliding panel.
So with the sliding panel out of the way, you can now remove the fixed door. The stationary door will be held in place with screws that go into the sliding door tracks.
Look for an L-shaped bracket screwed onto the track and corner of the stationary door panel. Use a screwdriver to loosen these screws in the bracket, then loosen the screws holding the door panel. Unlike the sliding door, the stationary door will be caulked where the panel meets the door jamb. You will need to use a utility knife to cut the caulk away from the panel carefully. Use a caulk remover to help soften the caulk before cutting into it. Once the caulk is cut, have your helper firmly hold the stationary panel.
Place your pry bar down between the bottom of the door panel and the track, then pry upward on the panel until you can pull the bottom of the panel toward you. If you are completely removing the sliding glass door to install a new door, you can now remove the door frame by using the pry bar.
You will be doing a lot of prying to free the frame from the door jamb. Use the claw end of the pry bar to remove the trim by grabbing the nail shafts. Use your reciprocating saw to cut along and through the sides and top. The bottom may be caulked or glued into place, so once the top and sides are free, have your helper assist you in pushing and tipping the frame away from your house. As your helper tilts the frame, keep prying with your pry bar to release the frame from the floor.
Once the frame is out, you can use the hammer claw to remove any exposed nails. Then, cut the frame into smaller pieces to make it easier to dispose of. Be very careful, however, because the pieces will be sharp and can cause you harm if handled improperly. To make this a less expensive remodeling project, you can remove the sliding glass door yourself and have a professional installer come to put the new door in.
If you want special upgrades or custom options, sliding glass doors may be more expensive. If this describes you, enter your information into the form below to be paired with a pro. With your sliding glass doors removed, your home will have a large opening that can be a security hazard until the new doors are installed.
Installation of new sliding glass doors takes about 4 to 6 hours. When you measure for a new door, find the width by measuring from one side of the door jamb to the other with a tape measure.
To find the length, start from the floor where the door sill is installed and up to the beam of the door. The average size for sliding glass patio doors is 80 inches tall and 60 to 72 inches wide.
If you decide to remove your sliding glass doors yourself, make sure to have a helper assist you with each step. When you remove the doors successfully, you can be proud of yourself for another home improvement project well done. Andrew Helling is the founder and editor of REthority.
He graduated from the University of Nebraska at Omaha where he obtained a Finance and Banking degree. As a formerly licensed real estate agent and property manager of single-family homes, Andrew knows real estate.
More About Andrew. Additional menu. Why Remove a Sliding Glass Door? Follow These Steps Removing a sliding glass door can be a physical challenge, but it is a relatively simple process to follow.
Tools and Materials Needed Flathead screwdriver or putty knife Phillips head screwdriver Pry bar Reciprocating saw Heavy blankets, cardboard, or foam sheets The flathead screwdriver or putty knife will help you tuck the sliding glass door rollers under the sliding panel as you pull it out.
Clear the Area Sliding glass doors are large, and once you remove the doors from their tracks, you will need plenty of space around the area so you can carefully lay the doors on the ground. Adjust the Screws Use either a flathead or Phillips screwdriver to turn both adjustment screws in a counter-clockwise direction, which tucks the sliding glass door rollers into the door.
Remove the Head Stop Your sliding glass door may have a doorstop that covers the inside edge of the door frame. Remove the Stationary Door Note : You may or may not need this step, depending on your purpose of removing the sliding glass door. Remove the Door Frame If you are completely removing the sliding glass door to install a new door, you can now remove the door frame by using the pry bar.